Admission

Credit Transfer Guidelines

The university policy governing credit transfer and course equivalence for students joining BAUET from other institutions.

Published Aug 23, 2026, 7:00 PM Updated Sep 20, 2026, 3:46 AM

Policy of Credit Transfer and Course Equivalence System

1. Preamble

Bangladesh Army University of Engineering and Technology (BAUET) follows an Outcome Based Education (OBE) curriculum to ensure that students achieve the required knowledge, skills, competencies, and Program Learning Outcomes (PLOs). This policy provides guidelines for credit transfer and course equivalence for students transferring from other universities or institutions into BAUET while maintaining compliance with:

  • Outcome Based Education (OBE)
  • BAETE and BAC Accreditation Standards
  • UGC, Bangladesh policies

2. Policy objectives

The objectives of this policy are to:

  • Ensure fair and transparent credit transfer
  • Maintain academic quality and accreditation standards
  • Ensure proper CLO-PLO equivalence
  • Preserve the integrity of BAUET programs
  • Facilitate student mobility between universities

3. Scope

This policy applies to:

  • Engineering Programs
  • Non-Engineering Programs
  • Local and international transfer students

4. Eligibility for Credit Transfer

A student may apply for credit transfer if:

  • The previous institution is recognized by UGC or appropriate authority
  • The course was completed within the last 2 years
  • The student obtained at least grade "C" or equivalent

5. Basis of Course Equivalence

Course equivalence shall be determined based on:

  • Course Learning Outcomes (CLOs)
  • Program Learning Outcomes (PLOs)
  • Course contents
  • Credit hours
  • Assessment methods
  • Laboratory or practical work
  • Contribution to program outcomes

For Engineering programs, the following shall also be considered:

  • Complex Engineering Problems (CEP)
  • Complex Engineering Activities (CEA)
  • BAETE and BAC requirements

6. Similarity Requirement for Course Equivalence

Course equivalence at BAUET shall be determined based on the percentage of similarity between the transferred course and the corresponding BAUET course. A course with 80% or higher similarity shall normally be considered for full equivalence. Courses having similarity between 70% and 79% may be considered for conditional equivalence, while courses with similarity between 60% and 69% may receive partial equivalence. Courses with less than 60% similarity shall not be accepted for credit transfer. In cases of conditional or partial equivalence, the student may be required to complete additional academic requirements such as bridge courses to satisfy the required learning outcomes and program standards of BAUET.

7. Dominating Course Policy

7.1 Definition

A "Dominating Course" refers to a core or major course that significantly contributes to the achievement of Program Learning Outcomes (PLOs) and accreditation requirements.

7.2 General Rules for Dominating Courses

  • Dominating courses shall not be fully eligible for direct credit transfer unless strict CLO-PLO equivalence is demonstrated.
  • A dominating course list shall be prepared by each department based on CLO-PLO mapping and approved by the appropriate authority.
  • Credit transfer for dominating courses shall require mandatory CLO mapping equivalence with at least 80% alignment with the corresponding BAUET course.
  • The departmental equivalence committee shall formally evaluate and certify PLO contribution before recommending transfer of any dominating course.
  • In cases of significant mismatch, dominating courses shall be rejected for transfer, and the student must complete the course at BAUET.

7.3 Limit of Dominating Course Transfer

A limit on dominating course transfer shall be imposed as follows:

  • Maximum 30-40% of core/dominating courses may be transferred within the existing overall credit transfer limit.

8. Engineering Program Requirements

For Engineering programs, transferred courses must demonstrate:

  • Acceptable PLO contribution
  • Appropriate cognitive, psychomotor and affective level
  • CEP and CEA exposure
  • Compliance with BAETE and BAC standards

The following courses are normally not transferable:

  • Integrated Design Project/Capstone Project
  • Thesis
  • Internship

9. Maximum Credit Transfer Limit

To maintain academic quality, institutional identity, and compliance with OBE and accreditation requirements, BAUET shall allow a maximum credit transfer limit of up to 60% of the total required credits for the programs. Students must complete the remaining required credits at BAUET in order to fulfill the academic, program outcome, and residency requirements of the university.

10. Credit Transfer Procedure

  1. 1

    Application Submission

    Student submits application with required documents.

  2. 2

    Document Verification

    The department verifies authenticity and eligibility.

  3. 3

    Course Mapping

    Courses are evaluated based on CLO-PLO mapping, course contents, assessment methods, and laboratory/project work.

  4. 4

    Gap Analysis

    Deficiencies in learning outcomes or PLO attainment are identified.

  5. 5

    Committee Decision

    The Departmental Equivalence Committee recommends full transfer, conditional transfer, partial transfer, or rejection.

  6. 6

    Final Approval

    Approval is provided by the competent academic authority.

11. Required Documents

Students must submit:

  • Credit transfer application form along with character certificate and no objection certificate from the previous institution
  • Official transcript
  • Course syllabus
  • Course outline
  • CLOs (if available)
  • Credit hour distribution
  • Assessment methods
  • Laboratory/project details (for Engineering programs)

*Additional documents may be required if necessary.

12. Approval Authority

Credit transfer shall be evaluated by:

  1. Head of the department / Academic committee / PSAC will check the necessary documents for equivalence
  2. BAUET equivalence committee will recommend the equivalence for approval
  3. The Academic council will give the final approval.

Legend

Bangladesh Accreditation Council (BAC)

Board of Accreditation for Engineering and Technical Education (BAETE)

Program Self-Assessment Committee (PSAC)